![anritsu instacal model icn50b anritsu instacal model icn50b](https://i.ebayimg.com/images/g/HuYAAOSwzo9dd~yi/s-l400.jpg)
To this Site Master is different than the oneĬurrently stored, it will display soft key options to keep or replace the InstaCal characterization data. If the Site Master senses that the characterization data for the InstaCal module connected Site Master senses the familiar InstaCal module and automatically calibrates the unit using the OSL procedure. Used to calibrate this Site Master before, the If this particular InstaCal module has been Up for the internal circuitry to stabilize. This procedure first on the S113C (or S115BQ)īefore continuing, allow a five minute warm S115BQ) and an S331C Site Master, perform
#ANRITSU INSTACAL MODEL ICN50B FULL#
If performing full verification over the entire
![anritsu instacal model icn50b anritsu instacal model icn50b](https://www.mst-as.cz/wp-content/uploads/2019/07/mw82119b-rightangle-capoff-2.jpg)
Theįrequency range of the S113C and S115BQ is 2 However, limited verification is possible with either instrument for theįrequency range of that instrument only. Its entire frequency range (2 - 4000 MHz) requires both an S113C (or S115BQ) and an Module, part number ICN50, is an optional accessory for the S113C, S331C, and S115BQ.įull verification of the InstaCal module over This test verifies the performance of the Anritsu Site To the input of the 560-7N50C RF detector. Measurement calibration of the Site Master is not required Site Master, the following test can be used to verify If the Power Monitor (Option 5) is installed in the When complete, ZERO ADJ:ON is displayed in the message area.Ĭonnect the output of the MA2418A Reference Source to the two attenuators soĪs to add 40 dB of attenuation (Figure 3). Press the ZERO soft key to zero the power Open/Short and 28N50-2 or SM/PL Termination.Ĭonnect the 20 dB offset to the Refl TestĬonnect the DC power supply to the appropriate line voltage to supply power to
![anritsu instacal model icn50b anritsu instacal model icn50b](https://i.ebayimg.com/images/g/c3UAAOSwIS9cJvtW/s-l640.jpg)
(m) Select 2 dB/Div (F3) and the press the (k) Press the 1, 0, and dBm keys sequentially to change the Reference Level (i) Press the Filter Off soft key (F3) to Measurement calibration of the Site Master is required for this test. The following test can be used to verify the accuracy (g) Press the 1, 0 and kHz keys sequentially to change the RBW to 10 kHz. (e) Press the 7, 5, 0, and kHz keys sequentially to change the Frequency (a) Press the Preset key, then select Preset All (F1). MeasurementĬalibration of the Site Master is not required for thisĬonnect the RF cable from the Site Master Reflection Test Port to the RF Input The following test can be used to verify the CW frequency accuracy of the Site Master. Optional power monitor is also available. It combines a synthesized source, VSWR Bridge, and receiver on a single printed circuit board (PCB). (standing wave ratio/return loss), and Distance-To-Fault measurement instrument. The Site Master (Figure 1) is a hand held SWR/RL Models S113C/ S331C and S115BQ having any version of firmware. Used to verify the performance of the Site Master Paragraphs 4 through 9 contain tests that can be Replacement procedures, and a replaceable parts list. Provides performance verification procedures, parts The Site Master S113C/S331C and S115BQ AntennaĪnd Cable Analyzer.
#ANRITSU INSTACAL MODEL ICN50B MANUAL#
This manual provides maintenance instructions for Site Master™ Models S113C, S331C and S115BQ